Were you looking for additional info concerning Tools You Need to Install a New Bathtub ?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Mounting a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and sometimes, tiling skills. Changing an old bath tub with a new one is also a moderately difficult job. If the old bathtub is easily easily accessible, the task can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. See to it you have qualified on your own for the work and are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Possibilities are you might require a professional plumber to make tube links.
This article will help you set up a brand-new bath tub in your washroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water pipes.
Your tools and material checklist ought to make up the following:
Preparing for the Installment
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be rather problematic because of the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, place the tub in the required setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the exact same for the various other tap.
Switch on the water system and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker offered backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, triggering the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our topic on How to Install a Bathtub. Thanks for taking time to read our blog. Enjoyed reading our blog entry? Please share it. Let somebody else locate it. We appreciate reading our article about Installing A Bathtub.
Schedule Estimate